Liebert POWER PROTECTION STATIC TRANSFER SWITCH Bedienungsanleitung Seite 139
- Seite / 152
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Event Message Help Text
131
CB3A (OUTPUT) OPEN
Circuit Breaker 3A (Output breaker) is Open (Optional)
Circuit breaker 3A is not closed. This circuit breaker is assigned to the output load. The power flow to the load cannot flow
through the static transfer switch.
Press SILENCE on the touch screen to turn off the audible alarm, if so configured. If you are accessing the STS2 system
from a terminal, type SH and press RETURN on your keyboard to turn off the audible alarm.
This event was written to the Event Log, if so configured.
The alarm has triggered a message to be sent to the modem, if so configured.
If configured to be a latching alarm, press RESET on the display. If you are accessing the unit from a terminal, type CA and
press RETURN on your keyboard.
S1 PHASE ROT ERROR
Source 1 Phase Rotation Error
A phase rotation error condition exists on Source 1. Check the phase sequence (ABC) of Source 1.
Transferring to Source 1 has been inhibited.
Press SILENCE on the touch screen to turn off the audible alarm, if so configured. If you are accessing the STS2 system
from a terminal, type SH and press RETURN on your keyboard to turn off the audible alarm.
This event was written to the Event Log, if so configured.
The alarm has triggered a message to be sent to the modem, if so configured.
If configured to be a latching alarm, press RESET on the display. If you are accessing the unit from a terminal, type CA and
press RETURN on your keyboard.
S2 PHASE ROT ERROR
Source 2 Phase Rotation Error
A phase rotation error condition exists on Source 2. Check the phase sequence (ABC) of Source 2.
Transferring to Source 1 has been inhibited.
Press SILENCE on the touch screen to turn off the audible alarm, if so configured. If you are accessing the STS2 system
from a terminal, type SH and press RETURN on your keyboard to turn off the audible alarm.
This event was written to the Event Log, if so configured.
The alarm has triggered a message to be sent to the modem, if so configured.
If configured to be a latching alarm, press RESET on the display. If you are accessing the unit from a terminal, type CA and
press RETURN on your keyboard.
- STATIC TRANSFER SWITCH 2 1
- 2
- TABLE OF CONTENTS 3
- IMPORTANT SAFETY INSTRUCTIONS 9
- OVERVIEW OF MANUAL 10
- 1.0 SAFETY PRECAUTIONS 11
- 2.0 UNPACKING AND INSPECTIONS 12
- WARNING 13
- 3.0 LOCATION CONSIDERATIONS 14
- 3.4 Altitude 15
- Max. Ambient Temperature 15
- Altitude—Feet 15
- 4.0 LOCATING THE STS2 16
- 5.0 POWER AND CONTROL WIRING 17
- 5.3 System Grounding 19
- 5.6 Power Supply 20
- 6.0 OPTIONS 21
- 6.5 Comms Board 22
- 6.6 Internal Modem 22
- 6.8 LED Display 23
- 6.9 Remote Source Selection 23
- 6.10 Key Lockout Switch 23
- 6.11 Redundant Output Breaker 23
- 6.13 Seismic Floor Anchors 24
- 6.14 Seismic Floor Stand 24
- 7.0 INSTALLATION DRAWINGS 25
- FRONT VIEW SIDE VIEW 26
- BOTTOM VIEW TOP VIEW 26
- DETAIL A 26
- FRONT VIEW 27
- SIDE VIEW 27
- TOP VIEWBOTTOM VIEW 27
- PS211101 REV. NO. 1 28
- PS211401 REV. NO. 1 29
- PS211801 REV. NO. 1 30
- PS211105 31
- Installation Drawings 32
- PS211805 33
- SECTION A-A 34
- ONE-LINE DIAGRAM 34
- PS214000 REV. NO. 3 40
- CONTROL WIRING 41
- REMOTE SOURCE SELECTION 43
- PS213001 44
- TABLE (J51) 45
- COMMS BOARD 46
- 02-810015-XX 46
- NETWORK INTERFACE 48
- CARD (NIC) 416241GX 48
- PS211005 50
- PS211000 51
- Figure 32 LED display 52
- PS215000 REV. NO. 0 53
- PS215001 Rev. 0 54
- PS215002 Rev. 0 55
- PS215003 Rev. 0 56
- PS216000 Rev.0 57
- PS216001 Rev. 0 58
- PS216002 Rev. 0 59
- PS216003 Rev. 0 60
- PS217000 Rev. 0 61
- PS217001 Rev. 0 62
- PS217002 Rev. 0 63
- PS217003 Rev. 0 64
- 8.1 System Description 65
- 8.2 Modes of Operation 66
- 8.3 Operator Controls 67
- 9.0 THEORY OF OPERATION 68
- Theory of Operation 69
- Hardware 70
- Firmware 70
- 9.2.2 Circuit Breakers 70
- 9.2.3 SCRs 70
- 9.2.4 Logic Modules 71
- 9.2.5 Audible Alarm 71
- 9.2.6 RS-232 Port 71
- 10.1 Normal System Turn-On 73
- 10.4 Maintenance Bypass 75
- 10.5 Normal System Shutdown 78
- 11.0 ALARM AND FAULTS 79
- 11.2 Event and History Logs 80
- 11.3 Alarm Notes 81
- 11.4 List of Messages 82
- Table 9 Event Messages 83
- 12.0 COMMUNICATION INTERFACES 84
- Groups Parameter 86
- Item Parameter 86
- Value Parameter 87
- Communication Interfaces 89
- 13.1 Display Overview 93
- 13.2 Menu Overview 94
- 13.2.1 Security 95
- Using the Password 95
- 13.3 Mimic Display 96
- 13.4 Event Controls 96
- 13.5 Event Display 96
- 13.6 Menu bar 96
- User Settings 97
- Source Set Points 98
- STS2 Touch Screen Display 100
- System Settings 101
- Comm Options 101
- Configuring the Modem 102
- Configuring Pager Support 103
- Dual Output Breaker 107
- SiteScan Configuration 107
- System Options 107
- 4 Pole Transfer Switch 108
- Wye Output Transformer 108
- Remote Source Selection 108
- System ID 108
- 13.6.2 Logs 109
- Event Log 109
- History Log 109
- 13.6.3 Source Transfers 110
- 13.6.4 Startup Procedure 110
- 13.6.5 Bypass Procedure 110
- 13.6.6 Help 110
- 13.6.7 Logo 110
- 14.1.1 Front Panel Controls 111
- 14.2 Operations 113
- 14.2.3 Maintenance Bypass 115
- 14.2.4 Normal System Shutdown 117
- 15.0 SPECIFICATIONS 118
- 15.1.4 Grounding 119
- 15.1.7 Response Time 119
- 15.2 System Components 120
- 15.2.4 Access 121
- 15.2.5 Circuit Breakers 121
- 15.2.6 Cable Entrance 121
- 15.2.7 Doors 121
- 15.2.9 RS-232 Port 122
- 15.2.12Maintenance Bypass 123
- 15.2.13Fuseless Design 123
- 15.2.14Options 123
- 16.0 EVENT MESSAGE HELP TEXT 124
- 17.0 MAINTENANCE 145
- SUPPORT INFORMATION 146
- Maintenance 150
Verwandte Produkte und Handbücher für Stromverteilungseinheiten (PDUs) Liebert POWER PROTECTION STATIC TRANSFER SWITCH
(156 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern